Selasa, 24 Mei 2011

Tugas Jarkom 2

Joanna Herpiani (11108079), 3ka15

Building a Hub-based Network

Background / Preparation

This lab focuses on the ability to connect two PCs to create a simple hub-based Ethernet LAN using

two workstations. A hub is a networking concentration device sometimes referred to as a multiport

repeater. Hubs are inexpensive and easy to install, but they permit collisions to occur. They are

appropriate for a small LAN with light traffic.

In addition to the physical and data link connections, which are Layers 1 and 2, the computers must

also be configured with the correct IP network settings, which is Layer 3, so that they can

communicate. Since this lab uses a hub, a basic Category 5/5e UTP straight-through cable is

needed to connect each PC to the hub. This is referred to as a patch cable or horizontal cabling,

which is used to connect workstations and a typical LAN. Start this lab with the equipment turned off

and with cabling disconnected. Work in teams of two with one person per PC. The following

resources will be required:

Two workstations with an Ethernet 10/100 NIC installed

Ethernet 10BaseT or Fast Ethernet hub

Several Ethernet cables, which are straight-through and crossover, to choose from for

connecting the two workstations

Step 1 Identify the proper Ethernet cable and connect the two PCs to the hub

a. The connection between the two PCs and the hub will be accomplished using a Category 5 or 5e

straight-through patch cable. Locate two cables that are long enough to reach from each PC to

the hub. Attach one end to the NIC and the other end to a port on the hub. Be sure to examine

the cable ends carefully and select only a straight-through cable.

b. What kind of cable is required to connect from NIC to hub? Straight Through Cable

c. What is the category rating of the cable?
Category 5 or 5e

d. What is the AWG wire size designation of the cable?
24 AWG

Step 2 Verify the physical connection

a. Plug in and turn on the computers. To verify the computer connections, insure that the link lights

on the both PC NICs and the hub interfaces are lit. Are all link lights lit?
They should be, otherwise troubleshoot.

Step 3 Access the IP settings window

Note: Be sure to write down the existing IP settings, so that they can be restored at the end

of the lab. These include IP address, subnet mask, default gateway, and DNS servers. If the

workstation is a DHCP client, it is not necessary to record this information.

Windows 95/98/Me users should do the following:

Click on Start > Settings > Control Panel and then click the Network icon.

Select the TCP/IP protocol icon that is associated with the NIC in this PC and click on

Properties.

Click on the IP Address tab and the Gateway tab.

Windows NT/2000 users should do the following:

Click on Start > Settings > Control Panel and then open the Network and Dial-up

Connections folder.

Click and open the Local Area Connection icon.

Select the TCP/IP protocol icon that is associated with the NIC in this PC.

Click on Properties and click on Use the following IP address.

Windows XP users should do the following:

Click on Start > Settings > Control Panel and then click the Network Connection icon.

Select the Local Area Network Connection and click on Change settings of this connection.

Select the TCP/IP protocol icon that is associated with the NIC in this PC.

Click on Properties and click on Use the following IP address.

Windows 7 users should do the following:

Click on Start > Control Panel
> Network and Internet
and then click the Network and Sharing Center.

Select the Change Adapter Settings in the right and click the Local Area Connection Icon and Click on Properties.

Select the TCP/IP protocol icon that is associated with the NIC in this PC.

Click on Properties and click on Use the following IP address.

Step 4 Configure TCP/IP settings for the two PCs

a. Set the IP address information for each PC according to the information in the table.

b. Note that the default gateway IP address is not required, since these computers are directly

connected. The default gateway is only required on local area networks that are connected to a

router.

Computer IP Address Subnet mask Default Gateway

PC – A 192.168.108.9 255.255.255.0 Not Required

PC – B 192.168.108.1 255.255.255.0 Not Required

Step 5 Access the Command or MS-DOS prompt

a. Use the Start menu to open the Command Prompt (MS-DOS-like) window:

Windows 95/98/Me users should do the following:

Start > Programs > MS-DOS Prompt

Windows NT/2000 users should do the following:

Start > Programs > Accessories > Command Prompt

Windows XP users should do the following:

Start > Programs > Accessories > Command Prompt

Windows 7 users should do the following:

Start > All Programs > Accessories > Command Prompt

Step 6 Verify that the PCs can communicate

a. Test connectivity from one PC to the other through the hub by pinging the IP address of the

opposite computer. Use the following command at the command prompt.

C:>ping 192.168.108.1 (or 192.168.108.9)

b. Look for results similar to those shown below. If not, check the PC connections and TCP/IP

settings for both PCs. What was the ping result?

Step 7 Confirm the TCP/IP network settings

Windows 95 / 98 / Me users should do the following:

a. Type the winipcfg command from the MS-DOS Prompt. Record the results.

__________________________________________________________________________

Windows NT / 2000 / XP users should do the following:

b. Type the ipconfig command from the Command Prompt. Record the results.

__________________________________________________________________________

Windows 7 XP users should do the following:

c. Type the ipconfig command from the Command Prompt. Record the results.

IP Address......................: 192.168.108.9

Subnet Mask.....................: 255.255.255.0

Default Gateway.................: 0.0.0.0

Step 8 Restore the PCs to their original IP settings, disconnect the equipment, and store the cables

1 komentar:

Danu mengatakan...

Terimakasih untuk informasinya, sangat membantu sekali.
Jangan lupa untuk kunjungi website kami